Del Mar Photonics
Rutile (TiO2) prisms and their applications - buy online - download brochure
Example of application:
High dispersion rutile prism for tuning dye lasers
Review of Scientific Instruments -- October 1976 -- Volume 47, Issue 10, pp.
J. Krasiski and W. Majewski
Institute of Experimental Physics, University of Warsaw, Hza 69, 00-681 Warsaw, Poland
A high dispersion rutile prism was constructed to tune dye lasers. With the help of this prism, a laser line was produced with smaller spectral width and greater strength than that obtained with the use of a 1800 grooves/mm diffraction grating. This prism is as durable as a glass prism.
Del Mar Photonics offers optical elements made of high quality synthetically
grown Rutile Titanium Dioxide crystals. Rutile’s strong birefringency, wide
transmission range and good mechanical properties make it suitable for
fabrication of polarizing cubes, prisms and optical isolators. Boules having
high optical transmission and homogeneity are grown by proprietary method.
Typical boules have 10 - 15 mm in dia. and up to 25 mm length. Optical elements
sizes - from 2 x 2 x 1 mm to 12.7 x 12.7 x 12.7 mm. Laser grade polish quality
is available for finished elements. So far we the largest elements that we
12 x15 x 5 mm, in which optical axis is parallel to 15 mm edge, 5 mm is
beam path, 12 x 15 mm faces polished 20/10 S/D, one wave flatness,
parallelism < 3 arc.min. (better specs. available on request).
|Standard Specifications (buy
Rutile (TiO2) coupling prism
Research description for a Rutile coupling prism
This description will give a brief insight into our research at the Light Technology Institute of the University of Karlsruhe (TH), Germany. One of our research fields is the development of electrically pumped organic semiconductor thin film lasers. Due to the complex behavior of these lasers numerous electrical and optical characterization is necessary. One of the most important optical properties of these organic semiconductor laser structures is the attenuation coefficient of the multilayer waveguide, which has to be carefully optimized to reduce waveguide losses 1. The first step in the optimization process is the numerical simulation of the anticipated waveguide design. Next, the optimized sample structure is fabricated and characterized in our attenuation measurement setup. This measurement is done as follows:
A Rutile coupling prism is pressed onto the waveguide. A laser beam is then coupled into the prism so that total reflection occurs inside the prism at the interface to the waveguide. In the vicinity of the waveguide the overlapping incident and reflected beam generate a standing wave. The evanescent field of that standing wave penetrates into the waveguide.
Evanescent field coupling
Under a certain angle and if the phase match conditions are fulfilled, the evanescent field stimulates a mode that is guided by the waveguide. The phase match condition can only be achieved when the refractive index of the prism is at least as high as the effective refractive index of the waveguide. Owing to its high refractive index, Rutile is an ideal material for use as a coupling prism in such a prism-coupler waveguide attenuation measurement setup.
Beam coupling into waveguide
A small fraction of the guided light is scattered out of the waveguide. The intensity of this scattered light is assumed to be proportional to the intensity of the guided light. Thus the intensity distribution inside the waveguide along the propagation direction can be directly determined through measuring the intensity of the scattered light.
Streak caused by scattering inside the waveguide
The intensity distribution is detected with a computer controlled, cooled CCD-Camera. Finally the attenuation coefficient is extracted from the measured data.
Intensity distribution measured with CCD-Camera
The following two figures show the setup that was used for the measurements.
Schematic of the Setup
Photography of the Setup
Additionally, it is possible with our setup to measure the refractive index and the thickness of waveguides that support a minimum of two guided modes. These parameters can be extracted from the dependency between coupling angle and effective refractive index.
Keywords: Prism, Coupling, Thin film waveguide, Waveguide losses, scattering, Effective refractive index, Organic semiconductor lasers, Polymer, Small molecule, Evanescent field, CCD-Camera, Coupling angle
1 M. Reufer, J. Feldmann, P. Rudati, A. Ruhl, D. Müller, K. Meerholz, C. Karnutsch, M. Gerken, and U. Lemmer, Appl. Phys. Lett. 86, 221102 (2005).
Universität Karlsruhe (TH)
Telefon: +49 721 608 7742
Telefax: +49 (0)721 608 - 2590
Del Mar Photonics